Photography by Kaya Blaze Kelley for Herb
No pipe? No papers? No problem. This is how to make a DIY bong that pulls perfectly every time.
Everyone has experienced it—you want to smoke weed but don’t have papers, a bong, or a pipe. Don’t fret. All you need is a handful of ordinary household items and a pinch of creativity.
Before we show you how to create a makeshift bong, we must warn you: this is definitely not the healthiest way to consume cannabis. This bong, and likely a few of its individual components, will be made out of plastic.
It’s never recommended to smoke out of plastic, as the heat from the smoke and the flame of the lighter may cause some of the plastic’s chemicals to leach into your system.
But, desperate times call for desperate measures. If you need a bong ASAP and are only smoking it for the day, the tips below should help.
Here’s how to make a bong at home that will get you through those frantic moments. If you really want to get creative, check out these homemade bong ideas.
Photography by Kaya Blaze Kelley for Herb
Before you do anything to your water bottle, construct what will become the shaft of your bong.
To do this, you’re just going to make a pen pipe. If you want a full, in-depth explanation (with photos) of how this is done, read this. Otherwise, I’ll paraphrase. The pen you use should ideally be made entirely out of metal.
But if that’s not possible, at least make sure it has an unscrewable metal top. Unscrew that top, and using a butter knife, pop out the little bottom piece.
Remove the ink tube, and any other little parts (like the spring) so that only the pen’s shaft and the metal screw-on top are left. Turn the metal screw on top upside-down and shove the pointed end into the pen’s shaft so that it stays firmly in the shaft. Discard any other pieces of the pen.
PRO ALTERNATIVE: Get yourself an Invincibowl. It’s an unbreakable metal bowl for bongs that provides the best smoke filtration without getting too hot. The Invicibowl will give your home made bong the filtration and quality of a premium bong. Find it in 6 vibrant colors to match your style.
If your water bottle isn’t already empty, empty it and remove the cap.
Next, you’re going to use a lighter to create a small hole in the bottom third of the water bottle. (Imagine two lines dividing the water bottle divided into three parts. The hole should be directly where the bottom line is).
To do this properly, make sure you have the empty pen pipe you just constructed on hand. Then, briefly hold the flame of your lighter against the water bottle’s bottom third.
Once you see a small hole open up in the bottle’s plastic, quickly shove the bottom of the pen pipe through the hole. If you do this correctly, since the plastic was still hot, it should mold pretty tightly around the pen shaft.
If the hole wasn’t big enough for the pen shaft to fit through, quickly hold the lighter against the plastic again, and try again. The bottom of the pen pipe should point downwards towards the bottom of the water bottle.
Photography by Kaya Blaze Kelley for Herb
No matter how talented you are at lighting holes in water bottles, chances are your shaft is not air-tight in your water bottle.
Therefore, you’re going to need to create a seal around its outside. The easiest way to do this is to chew up a piece of gum, then wrap it around the pen shaft right where it connects to the water bottle, creating a seal.
Photography by Kaya Blaze Kelley for Herb
Fill up your water bottle, but just enough so that a portion of the pen shaft is under water. Do not fill up the water bottle enough that the water meets the part of the bottle where the pen penetrates the bottle or the gum will get wet and may fall off.
You should have a fully functioning DIY water bottle bong! All you need to do is fill up the metal pen tip with cannabis and light it while inhaling through the top of the water bottle.
Other articles you can be interested in:
Making a bong out of a Gatorade bottle is a popular choice. Again, the plastic isn’t preferred since it can potentially lead to health risks since you’ll likely inhale chemicals contained within the plastic when heating it up.
But, binds are binds, and sometimes, that gatorade bottle is all we have.
Materials Needed:
Instructions:
Herb Recommended Products:
READ MORE